Please select the type of issue to find your solutions
LatteGo
Milk foam
Brew group
Noise
Alarm light/message
No/few drops of coffee
Coffee quality
Leaking
Grinding
On/Off
LatteGo
Some frequently asked questions about our LatteGo milk system
1. 2. 1. 2.
This may have two causes:
Milk may leak from the hole in the bottom of your Philips LatteGo milk frother when you have not assembled the two parts properly. Connect the two parts to each other until you hear a **click**. Please note that this may require some force.
When you unpack LatteGo, you have to remove the transport clip before you can use your milk frother.
The small hole in the bottom lets the milk flow into the frothing chamber through the channel that is created by the milk container and the seal on the LatteGo frame.
It is normal that there is some milk left behind in the milk container after use. This is necessary to ensure a perfect frothing result and to prevent air from being drawn in at the end of the frothing process.
If the amount of milk left behind in the milk container is larger than usual, please check the following.
If you did, you cannot use the indications on the frame as reference because you customized the milk quantity for the drink.
There is more milk in the milk container after frothing because you filled the container beyond the required level for the drink. Make sure that you fill the milk container to the required level for one or two cups of cappuccino or latte macchiato.
LatteGo can only be used on the machines it is sold with. It cannot be exchanged with other milk frothing systems.
My machine doesn’t create good milk foam
I cannot remove the brew group
I cannot insert the brew group
The machine is making a loud noise
The ‘empty container’ message doesn't
disappear
The descaling light does not go off after descaling
I don’t understand the meaning of the light signals on my machine
The coffee machine brews watery coffee
Only a few drops of coffee are being dispensed
No coffee or water is being despensed
The machine seems to be leaking water
The machine is not grinding the coffee beans
The machine will not switch on
I cannot remove the brew group
Philips 3200 Series LatteGo
If you cannot remove the brew group, the machine is not in the neutral position. Follow the steps below in order to be able to remove the brew group. Never remove the brew group during descaling. Always finish the descaling process first.
1. Replace the coffee grounds container and the drip tray and close the service door.
2. Switch the machine off. Wait until it is completely switched off and you hear no more sounds (this can take up to 15-20 seconds).
3. Switch the machine back on. Wait again until it is completely switched on and you hear no more sounds.
4. Remove the coffee grounds container and the drip tray, open the service door and try again to remove the brew group.
Philips 2200 Series
Philips 2200 Series LatteGo
Philips 3200 Series
Was this information useful?
Yes
No
I cannot insert the brew group
If you cannot insert the brew group, the machine and brew group are not in the neutral position. Follow the steps below to set the machine and brew group in neutral position:
1. Replace the coffee grounds container and the drip tray. Close the service door, but leave out the brew group.
2. Switch the machine off. Wait until it is completely switched off and you hear no more sounds (this can take up to 15-20 seconds).
3. Switch the machine back on. Wait again until it is completely switched on and you hear no more sounds.
4. Set the brew group to its neutral position. Watch the movie below for instructions.
5. Remove the coffee grounds container and the drip tray, open the service door and try again to insert the brew group.
Philips 2200 Series
Philips 2200 Series LatteGo
Philips 3200 Series
Philips 3200 Series LatteGo
Was this information useful?
Yes
No
Why doesn’t my machine create good milk foam?
If the milk carafe is not frothing the milk, there can be various causes and solutions. 1. The parts of the milk system are dirty. Detach all parts of the milk system, including the tubes, and clean them. It is best to use cold milk directly from the refrigerator at a temperature of 4 degrees. Semi-skimmed or full-fat cow's milk, soy milk and lactose-free milk have been tested and proven to give good froth.
2.The milk tube is not properly connected to the frothing element or cappuccinatore.
Attach the milk tube properly to the frothing element or cappuccinatore.
3.The milk is not cold.
4. You’re not using the correct type of milk.
Was this information useful?
Yes
No
The machine is making a loud noise
Prepare AquaClean filter
Sounds are normal when using your espresso machine. If you hear unusual noises, discover here what could cause this and how to easily resolve it. 2. The grind setting is set to the finest grind. Loud noise during rinsing or brewing might be caused by: 3. The machine needs to be descaled. 4. When using an AquaClean/Brita filter The filter was not prepared properly before installation or might be clogged. Switch off the machine. Remove the filter and try again to brew a coffee. If this works, make sure the filter is prepared properly before placing it back, see movie how to prepare the AquaClean filter. Place back the prepared filter and brew a coffee. If this still does not work the filter might be clogged and needs to be replaced.*The support movie is applicable for all Full Automatic Espresso machines, not only the mentioned models.
Loud noise during grinding might be caused by:
1. A blocked coffee funnel.
Unblocking the coffee funnel might solve the problem. Follow the steps in the support movie* how to clean.
Adjust the grind setting to a courser grind. Follow the steps in the support movie* first time use and how to customize settings.
1. Coffee beans/particles trapped under the water tank and air is drawn
Remove the water tank and remove any beans/bean particles located in the water tank compartment area. Follow the steps in the support movie* how to clean.
2. The brew group is clogged by dirt or not well greased
Remove the brew group and rinse it under the tap, grease if needed. Follow the steps in the support movie* how to clean for cleaning instructions and how to insert and remove the brew group.
If you have not descaled the machine in a while or postponed it a few times, it is now time to descale the machine. Only descale the machine with the Philips/Saeco decalcifier. On the descaling page you can find the correct instructions for your machine.
Was this information useful?
Yes
No
Service key error code 1, 3, 4, 5, 14 or 19 appears in the display
Error code 1 support movie
Error code 3/4 support movie
Error code 5 support movie
When error code 1, 3, 4, 5 or 14 is shown on the display, check the solutions below.
If any other code appears, we advise you to contact our Consumer Care Center for assistance
E01 The coffee funnel is blocked by ground coffee. 1. Take out the brew group and clean the coffee funnel with a spoon handle. 2.If there is no pre-ground coffee funnel, insert the spoon handle into the coffee funnel from below.
To unblock the coffee funnel;
E03 The brew group is clogged or has not been properly greased. 1.Rinse the brew group with fresh water, paying particular attention to the filter. 2.Grease the brew group as described in the cleaning and maintenance section.
E04 The brew group is clogged, has not been properly greased or is not locked in position. 1.Rinse the brew group with fresh water, paying particular attention to the filter.
2. Grease the brew group as described in the cleaning and maintenance section.
3. Replace the brew group and make sure it is locked into place. You hear a soft click when it is correctly inserted and locked.
4.Switch the machine off and back on.
E05 As there can be multiple causes, please contact our Consumer Care Center for assistance.
E14
Was this information useful?
Yes
No
The ‘empty coffee grounds container’ message does not disappear
If the coffee grounds container is emptied while the machine is switched off, the coffee cycle counter is not reset and the ‘empty coffee grounds container’ message does not disappear. To make the message disappear:
• Remove the coffee grounds container while the machine is switched on, wait at least 5 seconds and then reinsert it.
Was this information useful?
Yes
No
The descaling light does not go off after descaling
If the descaling light is still on then most probably you have not rinsed the machine with sufficient water after the descaling cycle was completed. Rinse your machine using another full tank of water. If you stopped the descaling procedure by switching off your machine and you don’t know how to resume, please contact our Consumer Care Center for assistance.
Was this information useful?
Yes
No
I don’t understand the meaning of the light signals on my espresso machine
The lights on your espresso machine give you information on what to do as well as on the status of your machine. The user manual contains a dedicated chapter on the meaning of the lights. Use this search function below to locate and download the appropriate user manual for your Philips or Saeco espresso machine. Note: If all lights are blinking simultaneously, please contact our Consumer Care Centre for assistance.
Search by product number.
Recommended results
{{fields.ISS_TITLE}}
We found {number} products that are available outside your country, so local promotions may not apply.
Show products Hide products
Found {number} products
Please select your model based on the last 2 digits of your product number shown in blue.
Found your model!
If this is the correct one, please select it below. Otherwise, search again.
Product image
Product description
Model number
Back to all products
{{#if product.imageURL}} 
{{ctnWithMarkTag product.dtn}}
{{#if product.handleID}}
{{product.handleID}}
{{/if}}
{{product.productTitle}}
{{/iff}} {{#iff product.cardWidth 'eq' 'small'}}
{{#if product.imageURL}}
{{ctnWithMarkTag product.dtn}}
{{#if product.handleID}}
{{product.handleID}}
{{/if}}
{{product.productTitle}}
{{/iff}}
