- October 29, 2023
- byjasco
Table of Contents
- BYJasco 33709 Universal Remote
- Setup
- Button Functions
- Programming Your Remote
- Using Your Remote
- Troubleshooting
- 90-Day Limited Warranty
- FCC Statement
- SPECIFICATION
- FAQS
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
The BYJasco 33709 Universal Remote Instruction Manual provides detailedinformation on how to set up and use the remote. The manual includesinstructions on battery installation, programming your remote, and using thevarious button functions. The remote is designed to control multipleaudio/video devices, and there are two different methods you can use toprogram the remote: Direct Code Entry or Auto Code Search. The manual alsoincludes information on the Master Volume Feature, Code Identification, andResetting to Factory Settings. For those looking for specific BYJasco remotecodes, the manual provides a Code List for different types of devices andbrands. With this comprehensive guide, users can easily set up and use theirBYJasco Universal Remote to control all their audio/video devices.
BYJasco 33709 Universal Remote
Setup
Your universal remote requires two (2) AAA batteries (not included). Alkalinebatteries are recommended.
Battery Installation
- On the back of the remote, pull down on the textured surface and slide the battery cover downward to remove it.
- Match the (+) and (-) marks on the batteries to the (+) and (-) marks inside the battery compartment, then insert two (2) AAA batteries. Be sure to use fresh batteries.
- Position the battery covers slightly below the opening and push upward to lock it into place.
NOTE: If your remote stops operating properly, replace the batteries withnew ones.
Battery Precautions
- Do not mix old and new batteries.
- Do not mix alkaline, standard (carbon-zinc), or rechargeable (Ni-Cd, Ni-MH, etc.) batteries.
- Always remove old, weak or worn-out batteries promptly and recycle or dispose of them in accordance with local and national regulations.
Battery Saver
Your remote automatically turns off if the buttons are depressed more than 8seconds. This will save your batteries should your remote get stuck in a placewhere the buttons remain depressed (e.g., between the sofa cushions).
Code Saver
You have up to 10 minutes to change the batteries in your remote withoutlosing the codes you have programmed.
Button Functions
- Power – turns devices ON/OFF
- Input – Selects video inputs
- TV, cbl, dvd, aux – Selects the device to control
- Record, play, stop, rewind, fast forward, pause
- DVD/Blu-ray™ open/close – open/close a player, or List features on cable/satellite receivers
- Setup – Used to program the remote
- ABCD – Access additional features for DVRs, cable and satellite receivers
- Home/Guide – Easily access features on today’s streaming devices, or Guide on cable/satellite receivers
- Menu – Displays the on-screen menu
- Up/Down/Left/Right menu navigation
- Ok – Selects menu items for the controlled device
- Exit – Exit on-screen menus
- Info – Displays on-screen show/content information
- Volume Up/Down
- Mute – Mutes sound
- Channel Up/Down
- Previous Channel – Returns to the previously selected channel
- Numbers – Enter numbers for direct channel selection
- Dot (•) – Used to select digital channels, e.g., 4.1
- Enter – Some devices require enter to be pressed after channel selection
Programming Your Remote
Your remote is designed to control multiple audio/video devices. To use, youwill need to program the remote for your devices. There are two differentmethods you can use to program the remote, Direct Code Entry or AutoCode Search.
- The Direct Code Entry method is the recommended method as it is the simplest and quickest method in most cases.
- The Auto Code Search method searches through all the codes in the remote to find a code for your device.
Note: This remote comes preprogrammed for Samsung TVs. Press TV forSamsung TVs.
Direct Code Entry (Recommended)
Locate the Code List included with your remote. Find the section for the type of device you wish to control, (for example TV, cbl, dvd, aux). Locate the brand of your device and circle all the remote codes for the brand.
Press and hold down the SETUP button on the remote until the red light on the remote control turns on. Release the SETUP button. The red light will remain on.
Note: The red light will either be a small light at the top of the remoteor the power ON/OFF button.Press and release the device button on the remote for the type of device you wish to control, (for example TV, cbl, dvd, aux ). The red light will blink once and remain on.
Note: Any of the device buttons on the remote can be programmed tocontrol any of your devices. For example, you can use the CBL device button onthe remote to control a Satellite Receiver, Digital Converter Box, StreamingMedia Player or any device category in the Code List.Use the number buttons on the remote to enter the first 4-digit remote code you circled in the Code List in Step 1. The red light will turn off after entering the fourth digit.
Point the remote at the device. Test the buttons on the remote to see if the device responds as you would expect. If the buttons do not operate the device return to Step 2 above and use the next code that you circled for that device.
Repeat Steps 1 – 5 for each device you wish to control.
Programming Notes
- Some codes may operate only a few functions of your device. There may be another code in the Code List that controls more functions. Test other codes in the Code List for more functionality.
- If you do not find a remote code that works your device or there are no codes in the Code List for your device, use the Auto Code Search method in the next section to program your remote.
- For combination devices such as a TV/DVD combo or TV/ VCR combo, you may have to enter a code for each device. (See Controlling Combo Devices. )
- Write down the remote codes used to program the remote for future reference.
Auto Code Search
The Auto Code Search is a process where you can search through all the codesstored in the remote to find a code for your device. It is recommended thatyou read through all the steps below to familiarize yourself with the AutoCode Search before starting the process.
Manually turn on the device you wish to control.
Note: The Auto Code Search process cannot be used for devices withoutpower ON/OFF capability. Use the Direct Code Entry method in these cases.Press and hold down the SETUP button on the remote until the red light on the remote control turns on. Release the SETUP button. The red light will remain on.
Note: The red light will either be a small light at the top of the remoteor the power ON/OFF button.Press and release the device button on the remote for the type of device you wish to control, (for example TV,cbl, dvd, aux ). The red light will blink once and remain on.
With the remote pointed at the device, press and release the POWER button on the remote. The remote will send 10 different codes to the device. The red light will blink once for each code and remain on after sending the 10 codes.
Did the device turn off?- If YES , go to Step 5.
- If NO , repeat Step 4 to test the next 10 codes.
Manual urn the device back on.
With the remote pointed at the device, press and release the VOL + button. The remote will re-send the first code of the 10 codes from Step 4. The red light will blink once and remain on.
Did the device turn off?
If YES, you have found a code for the device. Press and release the same device button you pressed in Step 3. This will store the code in the remote. Go to Step 7.
If NO, continue to press and release the VOL + button until the device turns off to test the other 9 codes from Step 4.
Be sure to wait approximately 3 seconds after each VOL + button press toallow the device time to respond to the code. When the device turns off, youhave found a code for your device. Press and release the same device buttonpressed in Step 3. This will store the code in the remote. Go to Step 7.
Notes:- The VOL – button can be used to go back through each batch of 10 codes.
- The red indicator light will flash 2 times after testing the first or last code in each batch of 10.
Use the remote to turn the device back on. Test the buttons on the remote to see if the device responds as you would expect. If the buttons do not operate the device, return to Step 2 and repeat this process to search for a better code to operate the device.
Repeat this process for each device you wish to control.
Controlling Combo Devices
Some combo devices (e.g. TV/VCR, TV/DVD, DVD/VCR, etc.) will require youto set up two different device buttons to control both parts of the combodevice. For example, if you have a TV/DVD combo, you may need to set upone code under the TV button to control the TV and a separate code under theb-ray button to control the DVD.
Using Your Remote
Master Volume Feature
The Master Volume Feature allows you to select a single device that the volumebuttons always control. For example, the remote can be in TV mode while thevolume buttons control the volume on your audio receiver or sound bar insteadof your TV.
Enabling the Master Volume Feature
- Press and hold down the SETUP button on the remote until the red light on the remote control turns on. Release the SETUP button. The red light will remain on.
- Press and release the device button (TV, aux, etc.) on the remote for the device you wish to control the volume.
- Press and release the MUTE button.
- Press and release the VOL+ button.
The red light will blink twice and turn off.
Disabling the Master Volume Feature
- Press and hold down the SETUP button on the remote until the red light on the remote control turns on. Release the SETUP button. The red light will remain on.
- Press and release the device button (TV, aux, etc.) programmed to control the Master Volume Feature.
- Press and release the MUTE button.
- Press and release the VOL – button.
The red light will blink twice and turn off.
Code Identification
- Press and hold down the SETUP button on the remote until the red light on the remote control turns on. Release the SETUP button. The red light will remain on.
- Press and release the desired device button (TV, cble, dvd, aux) you would like the code for.
- Press and release the ENTER button.
- Press and release the #1 button. Count the number of times the remote light flashes. This is the number corresponding to the first digit of the code. Repeat the process by pressing the #2, #3 and #4 buttons for the remaining digits.
- Press and release the ENTER button to exit this mode.
Reset to Factory Settings
- Press and hold down the SETUP button on the remote until the red light on the remote control turns on. Release the SETUP button. The red light will remain on.
- Press and release the MUTE button.
- Press and release the number #0 button. The red indicator light will flash twice.
Troubleshooting
Remote does not operate your device.
- Make sure the batteries are fresh and installed correctly.
- Aim the remote directly at your device, and make sure that there are no obstructions between the remote and device.
- Make sure you select the appropriate device on the remote you wish to control; TV for TV and CBL for cable box.
- Try programming the remote with a different code. See Direct Code Entry section.
- Remote may not be compatible with your device.
Remote does not operate some features of your device.
- Sometimes a particular code might operate a few features but not all. Try programming the remote with a different code from the Code list. See Direct Code Entry section.
- Remote may not be able to operate all features of your device or button names may be different than that of your original remotes.
SAVE THIS MANUAL AND CODE LIST FOR FUTURE REFERENCE
Scan this to view a helpful remote setup video http://www.byjasco.com/remote
If you have any questions or would like additional information please, visitour website:www.byjasco.com, or contact ourTechnical Support Group at 1-800-654-8483, Monday-Friday 7:00 am-8:00 pm CST.
90-Day Limited Warranty
Jasco Products Company warrants this product to be free from manufacturingdefects for a period of 90 days from the original date of consumer purchase.This warranty is limited to the repair or replacement of this product only anddoes not extend to consequential or incidental damage to other products thatmay be used with this unit. This warranty is in lieu of all other warrantiesexpress or implied. Some states do not allow limitations on how long animplied warranty lasts or permit the exclusion or limitation of incidental orconsequential damages, so the above limitations may not apply to you. Thiswarranty gives you specific rights, and you may also have other rights whichvary from state to state. If unit should prove defective within the warrantyperiod, return prepaid with dated proof of purchase to:
Jasco Products Company 10 E. Memorial Road
Oklahoma City, OK 73114
www.byjasco.com
MADE IN CHINA
GE is a trademark of General Electric Company and is under license by JascoProducts Company LLC, 10 E. Memorial Rd., Oklahoma City, OK 73114.
This Jasco product comes with a 90-day limited warranty. Visitwww.byjasco.com for warranty details.
Questions? Contact us at 1-800-654-8483 between 7:00 AM—8:00 PM CST.
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject tothe following two conditions:(1) this device may not cause harmfulinterference, and (2) this device must accept any interference received,including interference that may cause undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio or TVinterference caused by unauthorized modifications to this equipment. Suchmodifications could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limitsfor a Class B digital device, pursuant to Part 15 of the FCC Rules. Theselimits are designed to provide reasonable protection against harmfulinterference in a residential installation. This equipment generates, uses andcan radiate radio frequency energy and, if not installed and used inaccordance with the instructions may cause harmful interference to radiocommunications. However, there is no guarantee that interference will notoccur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined byturning the equipment off and on, the user is encouraged to try to correct theinterference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
ICES-3(B)/NMB-3(B).
Download PDF:BYJasco 33709 Universal Remote InstructionManual
SPECIFICATION
| Product | BYJasco 33709 Universal Remote |
|---|---|
| Battery Type | 2 AAA Alkaline batteries (not included) |
| Button Functions | Power, Input, TV, cbl, dvd, aux, Record, play, stop, rewind, |
fast forward, pause, DVD/Blu-ray open/close, Setup, ABCD, Home/Guide, Menu,Up/Down/Left/Right menu navigation, Ok, Exit, Info, Volume Up/Down, Mute,Channel Up/Down, Previous Channel, Numbers, Dot (•), Enter
Programming Methods| Direct Code Entry, Auto Code Search
Master Volume Feature| Allows control of a single device’s volume
Code List| Provides codes for different types of devices and brands
Code Identification| Made in China
FAQS
What is Code Identification?
Code Identification is a statement included in the manual that indicates wherethe BYJasco Universal Remote was manufactured, which is China in this case.
How do I disable the Master Volume Feature on my BYJasco Universal Remote?
Press and hold down the SETUP button on the remote until the red light on theremote control turns on. Release the SETUP button. The red light will remainon. Press and release the device button (TV, aux, etc.) programmed to controlthe Master Volume Feature. Press and release the MUTE button. Press andrelease the VOL – button. The red light will blink twice and turn off.
How do I enable the Master Volume Feature on my BYJasco Universal Remote?
Press and hold down the SETUP button on the remote until the red light on theremote control turns on. Release the SETUP button. The red light will remainon. Press and release the device button (TV, aux, etc.) on the remote for thedevice you wish to control the volume. Press and release the MUTE button.Press and release the VOL+ button. The red light will blink twice and turnoff.
How do I program my BYJasco Universal Remote?
There are two different methods you can use to program the remote: Direct CodeEntry or Auto Code Search. The Direct Code Entry method is the recommendedmethod as it is the simplest and quickest method in most cases. Locate theCode List included with your remote. Find the section for the type of deviceyou wish to control, (for example TV, cbl, dvd, aux). Locate the brand of yourdevice and circle all the remote codes for the brand. Press and hold down theSETUP button on the remote until the red light on the remote control turns on.Release the SETUP button. The red light will remain on. Press and release thedevice button on the remote for the type of device you wish to control, (forexample TV, cbl, dvd, aux). The red light will blink once and remain on. Usethe number buttons on the remote to enter the first 4-digit remote code youcircled in the Code List in Step 1. The red light will turn off after enteringthe fourth digit. Point the remote at the device. Test the buttons on theremote to see if the device responds as you would expect. If the buttons donot operate the device return to Step 2 above and use the next code that youcircled for that device.
What are the button functions on the BYJasco Universal Remote?
The BYJasco Universal Remote has various button functions including Power,Input, TV, cbl, dvd, aux, Record, play, stop, rewind, fast forward, pause, DVD/Blu-ray open/close, Setup, ABCD, Home/Guide, Menu, Up/Down/Left/Right menunavigation, Ok, Exit, Info, Volume Up/Down, Mute, Channel Up/Down, PreviousChannel, Numbers, Dot (•), and Enter.
How do I install the batteries in my BYJasco Universal Remote?
On the back of the remote, pull down on the textured surface and slide thebattery cover downward to remove it. Match the (+) and (-) marks on thebatteries to the ( + ) and ( – ) marks inside the battery compartment,then insert two (2) AAA batteries. Be sure to use fresh batteries. Positionthe battery covers slightly below the opening and push upward to lock it intoplace.
Read User Manual Online (PDF format)
Loading......
